Topkapi Lucida UV / gloss varnish 0.75lt

Aemme Colori

Article number :  VEN-6BUV00-1000

https://duvoisin-nautique-et-sports.odoo.com/web/image/product.template/348303/image_1920?unique=12fe350

62.90 CHF 62.9 CHF 62.90 CHF

68.00 CHF

Contact us for more details

    This combination does not exist.

    VEN-6BUV00-1000

    One-component, clear gloss polyurethane, non-yellowing varnish for a long lasting finish highly resistant to the marine environment. Easy to apply is recommended for the exterior clear finish of wooden boats. Formulated with addition of UV filters to withstand sun exposure.

    Paint Type: One component
    Binder type A: Alkyd-urethane
    Specific gravity kg/lt (±0,05): 0.920
    Solids content (volume) ±2: 56%
    Viscosity Ford ø 8 at 20°C ±2 : 90-120 sec. (Ø4 a 20°C)
    Shelf life (+10+30°C) : 18 months in airtight cans
    Viscosity Ford Ø4 : 90-120 sec.

    Application: Brush-Roller-Spray
    Brush-Roller: 10-15% Thinner 107 or 109
    Spray: 10-20% Thinner 900
    Touch dry: 4 h (20°c)
    Recoat time: 24 h (20°c)
    Application temperature: Between +10 C and +40 C
    Relevant humidity: Less than 80%
    Dry film thickness advised: 40 microns per coat
    Theoret. coverage m2/Lt: 12-14


    SURFACE PREPARATION AND APPLICATION PREPARATION

    Bare Wood. The surface should be clean and dry, sandpapered and dusted off. Apply a first coat of TOPKAPI LUCIDA UV onto bare wood, highly diluted up to 50-70% (depending on wood absorption) in order to allow the varnish to sink into the wood substrate. (As a clear primer alternative, one coat of POLIGLASS two-component varnish diluted 50-100% (depending on wood absorption) with Thinner 203 can be applied#chr(59)# care should be taken in order to maintain the grain of the wood open so to enable the application of subsequent coats of TOPKAPI LUCIDA UV. Overcoat then with 4-5 coats of TOPKAPI LUCIDA UV to obtain a high quality gloss finish, allowing the required recoat time between coats.

    Previously Varnished Wood. If the old paint is in poor conditions, loose or powdery, it should be mechanically removed. Clean the surface well and follow application directions as per bare wood.

    If the old paint is in good condition of adhesion and it only needs a topcoat because it is dull or dirty but with the underneath coatings still well fixed to the substrate (with no cracks or bubbles), clean,degrease and sandpaper with medium-fine abrasive paper and apply 2-3 coats of TOPKAPI LUCIDA UV to obtain a high quality gloss finish, allowing 24 hours between coats.

    SAFETY PRECAUTIONS
    Before starting paint application please carefully read all the safety precautions indicated on the label of each can or in the product safety data sheet available on request. For further information please do not hesitate to contact our technical staff.

    NOTES
    The above information is given to the best of our current knowledge, however, because the conditions of use of our products are beyond our control, no warranty is given or to be implied in respect of such information. Our technical staff can be contacted to study customer's specific requirements involving our products in order to enable their most effective use. Dilution rates and drying times must be considered only indicative, mainly related to a temperature of 20 ° C (68°F) and may vary according to prevailing temperature, in presence of particular weather conditions or depending on application procedures.
    Note: In the summer season or when temperatures are higher than 20°C, it is recommended for brush application the use of flowing THINNER 107/109.